Golden samples and first-article inspection: how the tenth reorder matches the first
A golden sample fixes what the part looks like; a first-article report proves it matches the drawing. Who signs the sample, where its three copies live, what an AS9102-style FAI holds, and what triggers a new one.
The tenth reorder matches the first only if there is something physical and something written to compare it against. The golden sample is the physical reference for appearance, workmanship and function; the first-article inspection report is the written proof that the first production-tooled part matches the drawing, dimension by dimension.
Without both, every later inspection compares parts against someone’s memory of what was approved. This post covers what each one is, who signs what, what goes into the report, and which changes at the factory mean the first article has to be done again. Where the two fit among the six checkpoints is in the supplier quality guide.
The golden sample: one approved unit, three places
A golden sample is a single unit, taken from production tooling and production material, that your engineer or quality lead has examined and approved as the standard. It is tagged with the part number, the drawing revision and the approval date, and signed. The factory’s quality lead countersigns the tag, so the factory cannot later say it agreed to something else.
It is retained in three places: one with you, one with your agent, one at the factory. Each copy has a different job. The factory’s copy sits where its own QC can compare against it during the run. The agent’s copy travels to the in-process check and the pre-shipment inspection, so the inspector is holding the same reference the factory is. Yours is the tie-breaker when the other two disagree, and the one you hand to your own receiving inspector.
For catalog goods, a promotional item or a packaging component, golden-sample approval may be the whole qualification. Where appearance is judged by eye, such as a color, a texture or a print, the cosmetic reference can include limit samples that show the worst acceptable condition, so “close enough” has a physical answer.
A golden sample is replaced, not amended. When a revision changes what the part looks like, the old samples are pulled and marked superseded, and new ones are signed and placed.
What a first-article report contains
For engineered parts, the golden sample is paired with a first-article inspection against the drawing. The FAI is done on parts from production tooling, production material and the production process, because a part made any other way proves nothing about the run. On the process page, it sits in the sample stage, after the DFM review and the T1–T3 tool samples and before any production quantity is ordered.
| Section | What it contains | What it proves |
|---|---|---|
| Ballooned drawing | Your drawing with every dimension, tolerance and note numbered | Nothing on the drawing was skipped |
| Dimensional report | For each balloon: the requirement, the measured value, the instrument used, pass or fail | The part matches the drawing, characteristic by characteristic |
| Cavity-by-cavity data | The dimensional report repeated per cavity on multi-cavity molds | Every cavity, not just the best one, makes the part |
| Material certifications | Mill or resin certificates traced to the lot used, where the drawing specifies material | The part is made of what you specified |
| Special processes | Plating, heat treatment, painting and the like, with the subcontractor named | Processes done outside the factory are identified and controlled |
| Functional test results | Fit, assembly, load or electrical tests, where the part has a function to test | The part works, not only measures |
| Cosmetic reference | Photographs against the golden sample and any limit samples | Appearance was judged against an agreed standard |
| Approval | Signatures from the factory and from your side, with dates | Someone accountable accepted the result |
The format borrows from AS9102, the aerospace first-article standard. Its three forms are a complete way to tie one part to one drawing: one for part identity and revision, one for materials, special processes and functional tests, and one for every characteristic on the drawing with its measured result. Buyers in other industries borrow it because it leaves no gaps, not because their part is going on an aircraft.
If your FAI report has no ballooned drawing, you cannot tell which dimensions were measured and which were assumed.
Approve before the production PO, not alongside it
The value of the FAI is its timing. A dimension out of tolerance at the first article is a conversation about steel on the tool. The same dimension found at pre-shipment is a conversation about a packed lot, and found at your dock it is a conversation about your line.
Suppose a buyer’s FAI shows one cavity of a four-cavity mold running a snap-fit boss 0.15 mm over the upper tolerance. The other three cavities pass. Approved as-is, a quarter of every lot carries a fit problem that a sampled inspection will catch only some of the time, because the pre-shipment inspection under ANSI/ASQ Z1.4 is a lot-acceptance decision on a sample, not a screen of every part. Caught at the FAI, it is a tool correction and a re-measurement of that one cavity before production starts. What a sampled inspection does and does not catch is worked through in AQL 2.5 and 4.0 explained for buyers.
Do not release a production PO until the FAI is signed and the three golden samples are in their three places. For machined, molded and stamped parts, the DFM review and documentation that lead into the FAI are described on the OEM components page.
How the reorder gets compared
Once the sample and the report exist, every later checkpoint is written against them. The in-process check at 20–30% of the run compares parts coming off the line with the golden sample and with the critical dimensions from the FAI. The pre-shipment inspection checklist takes its dimensions, functions and cosmetic standard from the same two documents. When a reorder comes six months later, the inspector arrives with the same sample and the same report.
That is the whole mechanism. The tenth order is not compared with the ninth, which would let small drift accumulate from lot to lot. It is compared with the first, as approved.
Keep the FAI report and a photo of the signed tag in the same file as every inspection report for that part number. The comparison is only as good as your ability to find the reference.
What triggers a new first article
An FAI proves that one combination of tool, material, process and place makes the part. Change any of them and the proof no longer covers what is being made. The supply agreement should list the triggers, and require the factory to notify you before the change, not after.
| Trigger | Example | What the new FAI covers |
|---|---|---|
| Engineering change | A written ECO revises a dimension or a note | The changed features, plus anything they affect |
| Tooling change | Mold repair or rework, a new cavity, a replacement die, tooling moved to another factory | Full FAI on the affected tool, every cavity |
| Material change | A different resin grade or steel supplier, even “equivalent” | Material certs, plus the dimensions and functions the material affects |
| New line or location | The part moves to a different press, line or building | Full FAI |
| Subcontractor change | A new plating, painting or heat-treatment supplier | The special process, coating or hardness checks, and appearance |
| Long gap between orders | Tooling has sat idle and setups have been lost | A first article on restart, at an interval agreed in the supply agreement |
Engineering changes go through the same paper as the original. A written ECO carries the revised drawing, the impact on tooling and price quoted back within five business days, and a new FAI on the changed features. Nothing changes on the shop floor without a signed revision.
The tooling-transfer row is the one buyers most often skip. If a tool moves to a second factory, the new factory’s first article is the only evidence that it makes the same part; how to do that without putting the tool at risk is in qualifying a second source without betting your tooling.
What to do with this
- Put your hand on the golden sample for each active part number. If you cannot find a tagged, signed, dated unit, the factory’s QC is comparing against something you never approved.
- Check that your FAI reports have a ballooned drawing and a measured value for every balloon. A report that says “all dimensions OK” is not a first article.
- Write the FAI triggers into the supply agreement, with notice required before the change. The quality and inspection page lists the checkpoints the sample and the report feed.
If the current factory has never been audited, that is the first thing a re-quote fixes. Send us the SKUs — ten business days, no fee, and the audit report is yours either way.