When China still wins: four kinds of part where moving costs more than it saves
Four kinds of part where a re-quote should say stay: Section 232 metals, deep-tooling parts, List 4A and unlisted headings, and cents-per-unit parts. The PP enclosure lands $2.77 from China and nets under 1% anywhere else.
A re-quote that never says “stay” is selling you a move. On a real set of parts, the honest result of running China against other origins at the 2026 tariff stack is that the incumbent keeps the work, and this post is about the four kinds of part where that result shows up most often.
The method behind it, picking an origin per part on landed cost rather than per country on headlines, is laid out in how to choose a sourcing origin per part. Every rate below is as of September 26, 2026 and is confirmed per HTS code before it goes on a quote. The four kinds share one trait: once the alternative’s FOB premium, freight, the agent fee and the cost of switching are all on the sheet, the gap to the incumbent is under 5%, and a gap under 5% does not pay for a qualification project.
1. Section 232 metal parts: the biggest duty line is the same everywhere
Since June 8, 2026, articles essentially all steel, aluminum or copper pay a 50% Section 232 duty on full customs value, and derivatives substantially made of them pay 25%, at any origin. Section 232 goods do not also pay the 12.5% or 10% from the July 24 Section 301 action. An FTA waives MFN; it does not waive Section 232. Under 15% metal content is exempt.
That changes what a move can buy. On a non-metal List 3 part, leaving China for an FTA-qualifying origin removes MFN plus 37.5 points of duty. On a metal List 3 part it removes MFN plus the 25% China list rate, and the 50% layer stays. On an unlisted metal heading the only duty that moves is MFN itself. The line that dominates the sheet is origin-blind, so FOB and freight decide.
Worse for the move, the 50% applies to the alternative’s higher FOB as well. An illustration with round numbers: a machined housing, essentially all steel, on a List 3 heading with MFN 2.5%, $10.00 FOB from China, ocean freight of 50 cents a unit.
| Per unit (illustrative) | China | Alt. origin · 12.5% duty | Alt. origin · FTA, 0% |
|---|---|---|---|
| FOB | $10.00 | $10.50 | $11.50 |
| Duty | $7.75 (77.5%) | $5.51 (52.5%) | $5.75 (50%) |
| Freight | $0.50 | $0.50 | $0.30 |
| Landed | $18.25 | $16.51 | $17.55 |
| Our fee, 10% of FOB | — | $1.05 | $1.15 |
| All-in | $18.25 | $17.56 | $18.70 |
The 12.5% origin nets 69 cents, 3.8%, on the strength of the 25-point list rate alone. The FTA-qualifying origin, with the lowest freight and no MFN, costs 45 cents more than staying. Neither clears the 5% line. The duty saving in the middle column is real, and the FOB premium plus the fee eat most of it, which is the pattern on metal parts generally. What the June 8 reset did to metal parts class by class, and when logistics rather than duty decide them, is in the June 8 Section 232 metals reset.
2. Parts where the incumbent’s tooling and process depth set the price
Some parts are cheap in China because of what has been built around them: a 16-cavity hot-runner mold that has long been paid off, secondary operations under the same roof, and a cluster of sub-suppliers within a day’s drive for inserts, springs, hardware and masterbatch. A second source quotes the same drawing without any of that. It quotes a new tool with fewer cavities, outsourced secondary operations, and imported sub-components that carry their own freight and duty.
The result is an FOB premium far larger than the 5% and 15% in the gasket example, and the premium eats the duty gap. Illustrative, round numbers: a two-shot overmolded part on a List 3 heading, MFN 2.5%, $2.00 FOB from China with the 16-cavity tool amortized. China pays 40.0% duty, 80 cents, plus 10 cents of freight, and lands at $2.90. The best alternative, an FTA-qualifying origin quoting from a new four-cavity tool, comes in at $2.70 FOB, no duty, 5 cents of freight, $2.75 landed and $3.02 all-in with the fee. China wins by 12 cents, about 4%, before anyone has paid for the second tool.
The tell is in the quote itself. When the alternative’s FOB sits 30% or more above China’s on a molded or multi-operation part, the premium is tooling and sub-supply rather than labor, and no duty gap short of a List 1–3 heading closes it. The move might still be right later, once the design is frozen and the volume justifies full cavitation at the second source. For now the sheet says stay.
3. List 4A and unlisted headings: a small duty gap to begin with
The duty gap between China and a 12.5% origin is the China list rate and nothing more. On Lists 1–3 it is 25 points. On List 4A it is 7.5 points, because China pays MFN plus 7.5% plus 12.5% against the alternative’s MFN plus 12.5%. On an unlisted heading it is nil: both pay MFN plus 12.5%. Only an FTA-qualifying origin changes the duty line on those parts, and what it removes is MFN plus 20 points on List 4A and MFN plus 12.5 on unlisted goods, against MFN plus 37.5 on a List 3 part.
The enclosure from our re-quote sheet is the standing example. Injection-molded PP enclosure, HTS 3926.90.99 (MFN 5.3%, List 4A): it lands $2.77 from China, $2.79 from a 12.5% origin and $2.50 from an FTA-qualifying origin. After the 10% fee the net is under 1%. It stays put, and the recommendation that goes with it is a better inspection plan at the factory the buyer already has.
The same molding process and the same buyer produced an 11% move on the gasket, because the gasket sits on List 3 and the enclosure on List 4A. The class decided it before the country did. Before quoting anything, read the list status for each heading. The parts on List 4A and unlisted headings need the arithmetic done, and the arithmetic often says no.
4. Cents-per-unit parts where qualification never pays back
A low-value, high-volume part can show a healthy percentage gap and still not be worth moving, because the gap in dollars is cents and the cost of qualifying a second factory is fixed. Audit, samples, first-article inspection, a pilot lot with inspection, an engineer’s time and often a new tool cost roughly the same for a 10-cent part as for a $10 part.
Illustrative, round numbers: a molded cap at $0.10 FOB from China on a List 3 heading, MFN 2.5%, 500,000 units a year. China pays 4 cents of duty and a cent of freight, 15 cents landed. An FTA-qualifying origin quotes $0.12, no duty, a cent of freight, and the fee adds 1.2 cents: 14.2 cents all-in. The saving is eight tenths of a cent a unit, $4,000 a year on half a million pieces. If duplicating the tool and running the qualification costs $20,000, the payback is five years, longer than the tool’s useful life and far longer than the tariff stack has held still at any point since January.
Compare the gasket at $1.20 FOB and 120,000 units a year, where the move nets $23,040 a year, 11% after the fee. The same $20,000 of tooling and qualification pays back there inside a year. Volume times cents is the number to look at, not the percentage.
What “stay” should look like
Staying in China is not the same as leaving things as they are. On every part above, the re-quote that says stay should also say three things.
First, whether the current factory has ever been audited and whether the inspection plan runs at the factory rather than at the dock. A defect caught at the molding machine is cheaper than any duty saved. The inspection system is the same at every origin, including the one you are already in.
Second, whether the part should stay single-sourced. A List 4A enclosure that should not move on duty can still carry a second qualified source, in China or elsewhere, with tooling you own, for the next port closure or factory failure. That is the China plus one program, and on these parts it is a resilience decision rather than a cost decision. How to run it without stopping the incumbent is in how to qualify a second source without betting your tooling.
Third, a date. The Section 232 reset runs through December 31, 2027, a second Section 301 investigation on excess capacity has been open since March 2026, and all four kinds of part above are one rate change from a different answer. “Stay” is a decision as of September 26, 2026, re-run every quarter; the method for that is in the quarterly origin review. The broader pattern of when each origin tends to win, metal included, is in nearshoring versus offshoring in 2026.
What to do with this
- Sort your parts by class before you sort them by country. Section 232 metal, Lists 1–3, List 4A, unlisted. The first and the last two are the usual stay candidates; Lists 1–3 are where moves pay.
- On any part where the alternative FOB is 30% or more above China’s, ask what the premium is made of. If the answer is tooling and sub-supply, the gap closes only when volume justifies full tooling at the second source.
- Multiply the per-unit saving by annual volume, then divide the qualification cost by that figure. A payback beyond two years, on a part with an open tariff investigation behind it, is a stay.
- Run the stays through the landed-cost calculator once a quarter at the current rates, and spend the effort you saved on the inspection plan.
Want this run on your parts? Send up to five SKUs and you’ll have a landed-cost comparison — China and other countries, named factories — in ten business days. No fee, no obligation.