The June 8 Section 232 metals reset: when moving a metal part offshore is a wash
Since June 8, 2026, a part essentially all steel, aluminum or copper pays 50% Section 232 duty from every origin, a derivative 25%. The duty gap that pays for a move nearly vanishes; FOB, freight and metal content decide instead.
Since June 8, 2026, an imported part that is essentially all steel, aluminum or copper pays a 50% Section 232 duty on its full customs value from every origin, and a derivative article substantially made of those metals pays 25%. For those parts the largest line in the duty stack no longer depends on where the factory is, and that removes the main reason a move paid for itself on other parts this year.
This post works through what the reset does to an origin decision, at the rates in force as of September 26, 2026, with an illustrative comparison in round numbers. The full method, with freight, working capital and the four classes of part, is in the landed-cost guide for importers, 2026 edition. Every rate below is confirmed per HTS code before it goes on a quote.
What the June 8 reset says
The Section 232 metals regime was reset on June 8, 2026 and runs through December 31, 2027. It applies 50% to articles essentially all steel, aluminum or copper and 25% to derivative articles substantially made of them, on the full customs value, at any origin. Parts under 15% metal content are exempt.
Two interactions with the rest of the stack matter. Section 232 goods are exempt from the July 24 Section 301 layer, so the 12.5% (10% for some economies) drops out. The China list rate still applies where the heading is on Lists 1–3 or List 4A, and a free-trade agreement waives MFN but not Section 232.
Put together, a Section 232 part on a listed heading pays MFN plus the list rate plus 232 from China, MFN plus 232 from a 12.5% origin, and 232 alone from an FTA-qualifying origin once the rule of origin is proven for the heading. The table is the Section 232 row from the guide, written out layer by layer.
| Section 232 part, listed heading | China | Alt. origin · 12.5% duty | Alt. origin · FTA, 0% |
|---|---|---|---|
| MFN | yes | yes | waived |
| China list rate (25% or 7.5%) | yes | no | no |
| July 24 Section 301 layer | no | no | no |
| Section 232 | 50% or 25% | 50% or 25% | 50% or 25% |
All as of September 26, 2026. The 232 line is the same in every column, and it is the big one.
Why the duty gap collapses
On a non-metal List 3 part with a 2.5% MFN, China pays 40.0% and an FTA-qualifying origin pays nothing: a 40-point gap, which is the gap that moves the gasket in the guide. Make the same heading essentially all steel and China pays 2.5 plus 25 plus 50, 77.5%, while the FTA origin pays 50%. The gap is 27.5 points, and every point of it is MFN and the China list rate; Section 232 contributes none.
Against a 12.5% origin the arithmetic is no better. Without metal, the gap between China and a 12.5% origin on a List 3 heading is 25 points. With Section 232 it is still 25 points, because the 12.5% layer drops out of both columns and the 232 goes into both. The move saves the same 25 points, but on a part whose duty is already 77.5% from China, the alternative’s higher FOB is taxed at 52.5% instead of 15%.
That last effect is the one buyers miss. A 15% FOB premium at the alternative origin costs 15% more FOB plus 50% duty on that premium, 22.5% in total, before freight and the fee. On a non-metal part the FTA origin’s 0% absorbed the premium easily. On a Section 232 part the premium is taxed at the same rate the saving was supposed to come from.
An illustrative comparison in round numbers
Suppose a machined steel part, essentially all steel, on a List 3 heading with a 2.5% MFN rate, quoted at $10.00 FOB from China. Apply the gasket’s FOB pattern, 5% higher at a 12.5% origin and 15% higher at an FTA-qualifying origin within truck range of the US, and a freight pattern that mirrors it. The figures are illustrative, built from the stated rates as of September 26, 2026, and would be confirmed per HTS code on a real part.
| Per unit (illustrative) | China | Alt. origin · 12.5% duty | Alt. origin · FTA, 0% |
|---|---|---|---|
| FOB | $10.00 | $10.50 | $11.50 |
| Duty, with Section 232 | $7.75 (77.5%) | $5.51 (52.5%) | $5.75 (50%) |
| Freight | $0.30 | $0.35 | $0.15 |
| Landed | $18.05 | $16.36 | $17.40 |
| Fee, 10% of FOB | — | $1.05 | $1.15 |
| All-in | $18.05 | $17.41 | $18.55 |
The FTA-qualifying origin, which wins the gasket by 11%, loses here by 50 cents a unit, 2.8% worse than staying. The 12.5% origin nets 64 cents, 3.5%, inside the band where lead time, MOQ and risk should decide rather than price.
Now take the metal out. Suppose the same part redesigned to under 15% metal content, so Section 232 does not apply and the July 24 layer returns: China pays 40.0%, the 12.5% origin 15.0%, the FTA origin 0%. With the same FOB and freight, all-in cost is $14.30 from China, $13.48 from the 12.5% origin and $12.80 from the FTA origin, a 10.5% saving at the best origin. Same factories, same prices, opposite answer. The duty class decided, not the country.
What decides a Section 232 part, since duty will not
With the 232 line equal everywhere, the comparison comes down to the lines that are not. The first is FOB. Every dollar of factory price on a 50% part costs $1.50 landed before freight, so a move only works with an equal or lower FOB, not a higher one that duty was supposed to cover. A factory that quotes 15% above China on a Section 232 part has to beat China by 15% on something else.
The second is freight and lead time. Metal parts are dense, and a container of them hits its weight limit before its cube, so freight per unit runs higher than the cube suggests and the ocean-versus-truck difference matters more. Lot size, transit working capital and safety stock go on the sheet beside freight, and for a Section 232 part they are most of what separates the origins. On the illustrative part, truck-range freight saved 15 cents a unit; it was not enough to cover a $1.50 FOB premium and the duty on it.
The third is the domestic quote. Section 232 applies to imports from any origin, and a part made in the US pays none of it and crosses no ocean. For a metal part the domestic column belongs on the sheet next to the others, priced the same way, with no assumption about which way it will go.
The fourth is the remaining list rate. On a listed heading China carries 25 or 7.5 points the other origins do not. On an unlisted heading it carries none, and a 12.5% origin and China then pay identical duty on a Section 232 part; only an FTA origin’s MFN waiver separates them, which on a 2.5% MFN is 2.5 points. That is a lead-time and MOQ decision, not a tariff one.
The 15% threshold, and what honest reclassification means
The exemption below 15% metal content is where the real decision sits, and it is a question of fact about the part, not a question of paperwork. Metal content comes from the factory’s bill of materials, by weight and by material, and the answer belongs in the quote file where a broker or an auditor can read it. A plastic housing with a steel threaded insert may be under the threshold; the same housing with a steel frame may not.
Re-engineering is legitimate when it changes the part. A bracket re-specified in glass-filled nylon for weight or corrosion reasons is a different article under a different heading, and it goes through DFM review, first-article inspection and the drawing like any other change. What is not legitimate is describing an all-steel part as something else, or splitting an assembly on the invoice so that each piece looks exempt. The duty follows what the article is at entry, and the importer of record signs for the classification.
Reclassification, honestly done, means checking that the heading on your entry summary actually describes the part. Headings get inherited from an old entry or a similar SKU, and a part that was never essentially all metal can sit on a Section 232 line because nobody re-read the heading. Ask your broker to defend the classification in writing, and where the heading is genuinely contestable, ask CBP for a ruling before the next entry rather than after a notice.
The ten common parts classified in what the July 24 tariff change did to ten common parts include a steel fastener and an aluminum bracket in this class. The step-by-step for placing your own heading, Column 1 rate first and metal check last, is in how to read your tariff stack by HTS code.
For the parts that stay essentially all steel, aluminum or copper, the honest position is that the duty is a wash across origins through December 31, 2027, and the decision is logistics, FOB and the factory’s quality system. Custom metal parts sit on the OEM components track, and the re-quote says “stay” on them when the arithmetic says so.
What to do with this
- Flag every part over 15% metal content by weight, from the factory’s bill of materials, and pull its 8-digit HTS code and Section 301 list status from the broker’s entry summary.
- Run the comparison with Section 232 in every column, including a domestic quote. The landed-cost calculator does not model Section 232, so do these on the sheet; treat anything under 5% as a tie to be decided on lead time and MOQ.
- Get the classification defended in writing by your broker, and where the heading is contestable, request a ruling before the next entry. How the ten business days of a re-quote are spent, classification included, is on the process page.
- Date the sheet. The reset runs through December 31, 2027, and the second Section 301 investigation is still open; either can change the answer.
Want this run on your parts? Send up to five SKUs and you’ll have a landed-cost comparison — China and other countries, named factories — in ten business days. No fee, no obligation.